VTSSErrorcode

  1 /** \brief Error code type */
  2 typedef int vtss_rc;
  3 
  4 /** \brief Error codes */
  5 enum
  6 {
  7     VTSS_RC_OK                                  =  0,  /**< Success */
  8     VTSS_RC_ERROR                               = -1,  /**< Unspecified error */
  9     VTSS_RC_INV_STATE                           = -2,  /**< Invalid state for operation */
 10     VTSS_RC_INCOMPLETE                          = -3,  /**< Incomplete result */
 11 
 12     VTSS_RC_ERR_CLK_CONF_NOT_SUPPORTED          = -6,  /**< The PHY doesn't support clock configuration (for SynceE) */
 13     VTSS_RC_ERR_KR_CONF_NOT_SUPPORTED           = -7,  /**< The PHY doesn't support 10GBASE_KR equalization */
 14     VTSS_RC_ERR_KR_CONF_INVALID_PARAMETER       = -8,  /**< One of the parameters are out of range */
 15 
 16     /**** 1G ERRORS ****/
 17     VTSS_RC_ERR_PHY_BASE_NO_NOT_FOUND           = -50,  /**< Port base number (first port within a chip) is not found */
 18     VTSS_RC_ERR_PHY_6G_MACRO_SETUP              = -51,  /**< Setup of 6G macro failed */
 19     VTSS_RC_ERR_PHY_MEDIA_IF_NOT_SUPPORTED      = -52,  /**< PHY does not support the selected media mode */
 20     VTSS_RC_ERR_PHY_CLK_CONF_NOT_SUPPORTED      = -53,  /**< The PHY doesn't support clock configuration (for SynceE) */
 21     VTSS_RC_ERR_PHY_GPIO_ALT_MODE_NOT_SUPPORTED = -54,  /**< The PHY doesn't support the alternative mode for the selected GPIO pin*/
 22     VTSS_RC_ERR_PHY_GPIO_PIN_NOT_SUPPORTED      = -55,  /**< The PHY doesn't support the selected GPIO pin */
 23     VTSS_RC_ERR_PHY_PORT_OUT_RANGE              = -56,  /**< PHY API called with port number larger than VTSS_PORTS*/
 24     VTSS_RC_ERR_PHY_PATCH_SETTING_NOT_SUPPORTED = -57,  /**< PHY API micro patch setting not supported for the port in question*/
 25 
 26     /**** MACSEC ERRORS ****/
 27     VTSS_RC_ERR_MACSEC_INVALID_SCI_MACADDR      = -60,  /**< From IEEE 802.1AE-2006, section 9.9 - The 64-bit value FF-FF-FF-FF-FF-FF is never used as an SCI and is reserved for use by implementations to indicate the absence of an SC or an SCI in contexts where an SC can be present */
 28     VTSS_RC_ERR_MACSEC_NOT_ENABLED              = -61,  /**< Trying to access port where MACSEC is not enabled*/
 29     VTSS_RC_ERR_MACSEC_SECY_ALREADY_IN_USE      = -63,  /**< Trying to use a secy which is already in use*/
 30     VTSS_RC_ERR_MACSEC_NO_SECY_FOUND            = -64,  /**< No SecY found for the specific port*/
 31     VTSS_RC_ERR_MACSEC_NO_SECY_VACANCY          = -65,  /**< No secy vacancy*/
 32     VTSS_RC_ERR_MACSEC_INVALID_VALIDATE_FRM     = -66,  /**< Validate_frames value invalid*/
 33     VTSS_RC_ERR_MACSEC_COULD_NOT_PRG_SA_MATCH   = -67,  /**< Could not program the SA match*/
 34     VTSS_RC_ERR_MACSEC_COULD_NOT_PRG_SA_FLOW    = -68,  /**< Could not program the SA flow*/
 35     VTSS_RC_ERR_MACSEC_COULD_NOT_ENA_SA         = -69,  /**< Could not enable the SA*/
 36     VTSS_RC_ERR_MACSEC_COULD_NOT_SET_SA         = -70,  /**< Could not set SA to in use*/
 37     VTSS_RC_ERR_MACSEC_INVALID_BYPASS_HDR_LEN   = -71,  /**< Invalid header bypass length*/
 38     VTSS_RC_ERR_MACSEC_SC_NOT_FOUND             = -72,  /**< Could not find SC (from sci)*/
 39     VTSS_RC_ERR_MACSEC_NO_CTRL_FRM_MATCH        = -73,  /**< No control frame match*/
 40     VTSS_RC_ERR_MACSEC_COULD_NOT_SET_PATTERN    = -74,  /**< Could no set bypass pattern for CP rule*/
 41     VTSS_RC_ERR_MACSEC_TIMEOUT_ISSUE            = -75,  /**< Internal timeout issue, bailing out*/
 42     VTSS_RC_ERR_MACSEC_COULD_NOT_EMPTY_EGRESS   = -76,  /**< Could not empty the egress pipeline*/
 43     VTSS_RC_ERR_MACSEC_AN_NOT_CREATED           = -77,  /**< AN not created.*/
 44     VTSS_RC_ERR_MACSEC_COULD_NOT_EMPTY_INGRESS  = -78,  /**< Could not empty the ingress pipeline*/
 45     VTSS_RC_ERR_MACSEC_TX_SC_NOT_EXIST          = -80,  /**< No tx SC found*/
 46     VTSS_RC_ERR_MACSEC_COULD_NOT_DISABLE_SA     = -81,  /**< Could not disable sa*/
 47     VTSS_RC_ERR_MACSEC_COULD_NOT_DEL_RX_SA      = -82,  /**< Could not delete rx sa*/
 48     VTSS_RC_ERR_MACSEC_COULD_NOT_DEL_TX_SA      = -83,  /**< Could not delete tx sa*/
 49     VTSS_RC_ERR_MACSEC_PATTERN_NOT_SET          = -84,  /**< Pattern not set*/
 50     VTSS_RC_ERR_MACSEC_HW_RESOURCE_EXHUSTED     = -85,  /**< HW resources exhausted*/
 51     VTSS_RC_ERR_MACSEC_SCI_ALREADY_EXISTS       = -86,  /**< SCI already exists*/
 52     VTSS_RC_ERR_MACSEC_SC_RESOURCE_NOT_FOUND    = -87,  /**< Could not find SC resources*/
 53     VTSS_RC_ERR_MACSEC_RX_AN_ALREADY_IN_USE     = -88,  /**< Rx AN is in use*/
 54     VTSS_RC_ERR_MACSEC_EMPTY_RECORD             = -89,  /**< Could not get an empty record*/
 55     VTSS_RC_ERR_MACSEC_COULD_NOT_PRG_XFORM      = -90,  /**< Could not program the xform record*/
 56     VTSS_RC_ERR_MACSEC_COULD_NOT_TOGGLE_SA      = -91,  /**< Could not toggle SA*/
 57     VTSS_RC_ERR_MACSEC_TX_AN_ALREADY_IN_USE     = -92,  /**< Tx AN is in use*/
 58     VTSS_RC_ERR_MACSEC_ALL_AVAILABLE_SA_IN_USE  = -93,  /**< All available SA's are in use*/
 59     VTSS_RC_ERR_MACSEC_MATCH_DISABLE            = -94,  /**< MACSEC match disabled*/
 60     VTSS_RC_ERR_MACSEC_ALL_CP_RULES_IN_USE      = -95,  /**< All CP rules of the specific type are in use*/
 61     VTSS_RC_ERR_MACSEC_PATTERN_PRIO_NOT_VALID   = -96,  /**< The pattern priority is not valid*/
 62     VTSS_RC_ERR_MACSEC_BUFFER_TOO_SMALL         = -97,  /**< Buffer to small, must be greater than VTSS_MACSEC_FRAME_CAPTURE_SIZE_MAX*/
 63     VTSS_RC_ERR_MACSEC_FRAME_TOO_LONG           = -98,  /**< Frame length is supposed to be less than the amount of data in the fifo*/
 64     VTSS_RC_ERR_MACSEC_FRAME_TRUNCATED          = -99,  /**< Frame is Truncated*/
 65     VTSS_RC_ERR_MACSEC_PHY_POWERED_DOWN         = -100, /**< Phy is powered down, i.e. the MacSec block is not accessible*/
 66     VTSS_RC_ERR_MACSEC_PHY_NOT_MACSEC_CAPABLE   = -101, /**< Port/Phy is not MacSec capable*/
 67     VTSS_RC_ERR_MACSEC_AN_NOT_EXIST             = -102, /**< AN does not exist*/
 68     VTSS_RC_ERR_MACSEC_NO_PATTERN_CFG           = -103, /**< No pattern is configured*/
 69     VTSS_RC_ERR_MACSEC_MAX_MTU                  = -105, /**< Maximum MTU allowed is 32761 (+ 4 bytes for VLAN)*/
 70     VTSS_RC_ERR_MACSEC_UNEXPECT_CP_MODE         = -106, /**< Unexpected CP mode*/
 71     VTSS_RC_ERR_MACSEC_COULD_NOT_DISABLE_AN     = -107, /**< Could not disable AN*/
 72     VTSS_RC_ERR_MACSEC_RULE_OUT_OF_RANGE        = -108, /**< Rule id is out of range. Must not be larger than VTSS_MACSEC_CP_RULES*/
 73     VTSS_RC_ERR_MACSEC_RULE_NOT_EXIST           = -109, /**< Rule does not exist*/
 74     VTSS_RC_ERR_MACSEC_CSR_READ                 = -110, /**< Could not do CSR read*/
 75     VTSS_RC_ERR_MACSEC_CSR_WRITE                = -111, /**< Could not do CSR write*/
 76 }; // Leave it anonymous.